Design Multis seeks strained trajectories, with the minimum of stability, meaning that they are designed and built to stay in position in which they are. The pitch stability is low, roll effects induced by the lace are almost nil. Large area of rudder and speed make them extremely manoeuvrable (RC scale aviation subscription).
There are different ways to build or assemble an RC plane. Number of kits are commercially available, more or less expensive and requiring more or less talent or by their manufacturer experience. Some kits are mainly made of foam and plastic or balsa. The construction consists of use cases for the fuselage and ribs and stiffeners for the wing.
The most robust models have structures made of wood or composite may also comprise wings expanded polystyrene covered with a wood veneer, often abachi. These models are usually heavier than traditional construction and therefore more suitable for motorized aircraft to gliders. The lighter constructions are generally reserved for the flight room (or indoor) in a windless environment.
The Racers are small propeller planes that are racing around 2, 3, or 4 poles, their speeds exceeding 250 km / h. These devices are generally inexpensive and offer fairly similar performance which focuses on the drivers skill. They are generally made of fiberglass; more resistant composite materials are used on the most stressed points during the flight. The wings are usually cored in order to reduce the weight (all devices must achieve a minimum weight but lighter wings allow more precise control).
A distinction is usually made between toys appliances and those so-called leisure. The planes are exclusively electric toys, to less power and require less skill to drive. They are therefore cheaper. The recreational aircraft are available in multiple variants, the small plane electric up the device to several thousand dollars and hundreds of cubic centimeters "under the hood".
The thickness of material (usually 3 - 6 mm) and the density of latter were the models were generally heavier (more than 5 pounds) and were consequently above the average speeds. The range has been designed using a type of motor support smart cartridge designed for engine types 40 (6.6 cm3). Amateurs have recently developed a range of new models using corrugated plastic or "Coroplast". These models are collectively called SPAD meaning "Simple Plastic Airplane Design". The fans SPAD concept touting the durability, ease of construction and lower costs versus balsa models, sometimes at the expense of weight and an unconventional design.
Some RC models are inspired by nature. It can be gliders having the appearance of a bird, but more often bird models powered by wing beats. Spectators are often very surprised to see such models fly, and birds are no less curious when such devices share their airspace. These factors, as well as the challenge posed by the construction of such a model, add to pleasure of driving, although there are now on the market, some models ready to mount such birds. Flapping wing models are known to ornithopter, which is the technical name of worn aerodynes and propelled by an oscillating wing.
Aerobatic - models designed to perform complex and aerobatics. Suitable experienced "pilots". In its mass is nizkoplan, midwing and biplanes. Equipped with internal combustion engines, electric motors or jet engines. Aerobatic models are both reminiscent of a real-existing prototype, or not
There are different ways to build or assemble an RC plane. Number of kits are commercially available, more or less expensive and requiring more or less talent or by their manufacturer experience. Some kits are mainly made of foam and plastic or balsa. The construction consists of use cases for the fuselage and ribs and stiffeners for the wing.
The most robust models have structures made of wood or composite may also comprise wings expanded polystyrene covered with a wood veneer, often abachi. These models are usually heavier than traditional construction and therefore more suitable for motorized aircraft to gliders. The lighter constructions are generally reserved for the flight room (or indoor) in a windless environment.
The Racers are small propeller planes that are racing around 2, 3, or 4 poles, their speeds exceeding 250 km / h. These devices are generally inexpensive and offer fairly similar performance which focuses on the drivers skill. They are generally made of fiberglass; more resistant composite materials are used on the most stressed points during the flight. The wings are usually cored in order to reduce the weight (all devices must achieve a minimum weight but lighter wings allow more precise control).
A distinction is usually made between toys appliances and those so-called leisure. The planes are exclusively electric toys, to less power and require less skill to drive. They are therefore cheaper. The recreational aircraft are available in multiple variants, the small plane electric up the device to several thousand dollars and hundreds of cubic centimeters "under the hood".
The thickness of material (usually 3 - 6 mm) and the density of latter were the models were generally heavier (more than 5 pounds) and were consequently above the average speeds. The range has been designed using a type of motor support smart cartridge designed for engine types 40 (6.6 cm3). Amateurs have recently developed a range of new models using corrugated plastic or "Coroplast". These models are collectively called SPAD meaning "Simple Plastic Airplane Design". The fans SPAD concept touting the durability, ease of construction and lower costs versus balsa models, sometimes at the expense of weight and an unconventional design.
Some RC models are inspired by nature. It can be gliders having the appearance of a bird, but more often bird models powered by wing beats. Spectators are often very surprised to see such models fly, and birds are no less curious when such devices share their airspace. These factors, as well as the challenge posed by the construction of such a model, add to pleasure of driving, although there are now on the market, some models ready to mount such birds. Flapping wing models are known to ornithopter, which is the technical name of worn aerodynes and propelled by an oscillating wing.
Aerobatic - models designed to perform complex and aerobatics. Suitable experienced "pilots". In its mass is nizkoplan, midwing and biplanes. Equipped with internal combustion engines, electric motors or jet engines. Aerobatic models are both reminiscent of a real-existing prototype, or not
Aucun commentaire:
Enregistrer un commentaire