The movement of a watch is supposedly the most vital part of the grandfather clock regulation. For timekeeping and controlling the hour strike and its chime, the movement is necessary. Weights and the pendulum are equally vital for the operation of the watch. The pendulum tends to be so important because it helps in regulating time hence one should adjust it well to keep correct time.
Normally, three weights are used to provide power to hour strike, time and chime which are the left, center and right weights respectively. These weights are important when operating the watch hence it is mandatory that they are present. Each weight is different, and they must be properly hanged to ensure that the watch operation is good.
A chain or cable is used to hang the weights from the movement, and they have to be raised after every seven days failure to which the wristwatch will stop working. The sounds made by the strike and chime emanate by hammers hitting several length rods. The rods usually make different sounds when the hammer hits them and the specific melodies are made by controlling the sequence that every hammer hits its rod.
A person should have an idea of how the wristwatch works and master the different components together with their different uses so that he can regulate this antique watch. It is wise to make sure that where you are placing the clock is flat so that it can be sturdy and firm to prevent falling. Adjusting all its levers is mandatory for stability.
Once you have stabilized the watch, you are required to hang the pendulums in their right positions. A colored plastic film is used to cover the disk to protect it from damage. The disc should thus be removed very carefully before you hang the pendulums. The procedure should be closely followed so as not to damage pendulums which tend to be so vital to the wristwatch.
After hanging the pendulums, you can then hang the weights. It is advisable to check the weights to make sure that they have been assembled properly and tightly. Also, you should ensure that the cables are fastened well in the cable pulleys then hang the weight on the pulleys.
If it chances that the watch contains the moon dial feature, you can as well set it alongside the other devices. This can simply be done by putting some form of pressure to the dial using only your fingers. Ensure that you rotate this dial towards the clockwise side but if it does not rotate, do try to force it. You can leave it to rest for a day or two and try again.
Once you have set the moon dial, you can now proceed to set the time. It is important to note that the hour hand is not supposed to be moved. Therefore, move the minute hand and the hour hand will move automatically. Also, when the hands are striking, avoid moving them then start the already regulated watch.
Normally, three weights are used to provide power to hour strike, time and chime which are the left, center and right weights respectively. These weights are important when operating the watch hence it is mandatory that they are present. Each weight is different, and they must be properly hanged to ensure that the watch operation is good.
A chain or cable is used to hang the weights from the movement, and they have to be raised after every seven days failure to which the wristwatch will stop working. The sounds made by the strike and chime emanate by hammers hitting several length rods. The rods usually make different sounds when the hammer hits them and the specific melodies are made by controlling the sequence that every hammer hits its rod.
A person should have an idea of how the wristwatch works and master the different components together with their different uses so that he can regulate this antique watch. It is wise to make sure that where you are placing the clock is flat so that it can be sturdy and firm to prevent falling. Adjusting all its levers is mandatory for stability.
Once you have stabilized the watch, you are required to hang the pendulums in their right positions. A colored plastic film is used to cover the disk to protect it from damage. The disc should thus be removed very carefully before you hang the pendulums. The procedure should be closely followed so as not to damage pendulums which tend to be so vital to the wristwatch.
After hanging the pendulums, you can then hang the weights. It is advisable to check the weights to make sure that they have been assembled properly and tightly. Also, you should ensure that the cables are fastened well in the cable pulleys then hang the weight on the pulleys.
If it chances that the watch contains the moon dial feature, you can as well set it alongside the other devices. This can simply be done by putting some form of pressure to the dial using only your fingers. Ensure that you rotate this dial towards the clockwise side but if it does not rotate, do try to force it. You can leave it to rest for a day or two and try again.
Once you have set the moon dial, you can now proceed to set the time. It is important to note that the hour hand is not supposed to be moved. Therefore, move the minute hand and the hour hand will move automatically. Also, when the hands are striking, avoid moving them then start the already regulated watch.
About the Author:
When you are searching for information about grandfather clock regulation, visit our web pages today. More details are available at http://www.customtime.net/routine-maintenance now.
Aucun commentaire:
Enregistrer un commentaire